Windows Server 2003 RELEASED

[mickchip]

thanks for the audio links and yes I would be willing to make a donation, waited a long time to have windows on the joggler, its awesome.

[danfoshizzle]

Thanks for all your appreciation, does anyone have any idea how to set up donations through paypal,

I have already done this,
https://www.paypal.com/cgi-bin/webscr?c ... aNonHosted

does that look right?

[danb79]

thanks for this its brilliant!

does anyone know how to install wmp 10 or 11 every "how to" ive tried mentions using xp compatability mode but this seems to be missing?

Just to add, ive installed motionjoy ps3 sixaxis pad driver and mame and it works great ive also installed GTA vice city plays ok!! just to add i have a fan on my joggler to stop throttling max 30c!! now to try overclocking any ideas?

[mrluke]

Hi guys having some problems with this

put on memory stick with the win32image programe

all loads up super fast , When on the windows screen i see " Found new hardware wizard , Which says it will not work untill i restart"

The touchscreen keyboard

and a message saying service failed to start at startup

And now it just sits ! , ive plugged a mouse into the Hub but it doesnt do nothing

Ive also tried this from a Hub and direct from the USB port and it just gets stuck .

Any one able to help ?

[danfoshizzle]

try rewriting the image and on first boot allow 10 minutes so all drivers to to settle, as booting from a different make of usb stick than the one i used to create windows takes a little while to settle down and install the new device id of your specific usb stick

[danfoshizzle]

Wait for pete to answer the overclocking question as he has already done this

[danfoshizzle]

And thanks mick for the first donation!

Much appreciated

[mrluke]

try rewriting the image and on first boot allow 10 minutes so all drivers to to settle, as booting from a different make of usb stick than the one i used to create windows takes a little while to settle down and install the new device id of your specific usb stick

thanks i left it for 30 mins last time .

any indication displayed on screen once its done ?

im using a sandisk Cruzer btw

regards
Luke

[mickchip]

danfoshizzle
Your welcome and keep up the good work, I now have Garmin mobile PC working with a USB GPS dongle, might try fitting a Joggler in my car.

[mrluke]

try rewriting the image and on first boot allow 10 minutes so all drivers to to settle, as booting from a different make of usb stick than the one i used to create windows takes a little while to settle down and install the new device id of your specific usb stick

thanks i left it for 30 mins last time .

any indication displayed on screen once its done ?

im using a sandisk Cruzer btw

regards
Luke

Ive left it again for 30 mins , same thing

The found new hardware wizard says " the hardware you installed will not work untill you reboot your PC" and thats for the USB mass storage device.

Its not totally frozen , as the clocks changing time . But the touchscreen remains unresponsive ?

[danfoshizzle]

try using a usb mouse plugged in to a usb hub,

Make sure the mouse is pluggen in from power on else windows might not see it.

[pacman99uk]

i have the same problem as mrluke, other problem is after it boots and come up with the service failed message and i have to cycle power off to restart it and the whole distro refuses to boot again (gets stuck at crcdisk.sys) so i have to format the pendrive and reinstall again from scratch.

[danfoshizzle]

the service failed message is nothing to worry about,

@pacman are you also using a sandisk cruzer?

[pete]

I did notice that it was faster to do an image over again and let it find the drivers rather than wait. I was able to boot the W2003 from the side USB port with or without a hub. I couldn't boot the image though using the inside USB port.

[mrluke]

i have the same problem as mrluke, other problem is after it boots and come up with the service failed message and i have to cycle power off to restart it and the whole distro refuses to boot again (gets stuck at crcdisk.sys) so i have to format the pendrive and reinstall again from scratch.

exactly the same , if i power off and turn back on gets stuck on crcdisk.sys

any way to insert a custom vbs ? when i insert the memory stick in my i can only see the 200mb partition.

[pacman99uk]

ok, i managed to get it all working with the pendrive (seagate 6gb micro hard drive) attached to a belkin usb 4 port hub and usb mouse.

I reinstalled a fresh OS, plugged it into the belkin hub with the mouse attached and then plugged in the power connector... the mouse wont work unless its booted from the start with it plugged in (rather than plugging a usb mouse in once the os boots to desktop) install any hardware windows drivers that come up and it will ask you to reboot, you should then be able to get back into your install without a reinstall (you have to cycle power when it reboots as it wont boot back off pendrive if oyu dont)

Touch-Screen doesnt work from first boot but by going to control panel > system and then to the hardware tab > Device Manager and find under the mouse section a HID-compliant mouse with a yellow exclamation. just right click it and select update drivers and follow the recommended settings it will reinstall and enable touch screen.

the realtek ethernet doesnt seem to be working either but i havent installed the latest drivers yet (just what 2003 was bundled with so ill try that later.

@dan thanks for the release, ill send a fiver your way

[pete]

Dan,
Your Paypal stuff works fine.

Pacman99uk; I was able to get the internal NIC to work fine by changing the autonegociation to 100Mbs Full. It just worked for me; but not sure if its the right way. BTW you will get some very odd MAC addresses unless you put in your own.

I'll try to set up an image with a whole bunch of USB devices working; IE: mouse, keyboards, wireless keyboard etc. Only thing though its seems to look at the device and device order on the USB bus.

[danfoshizzle]

No worries pac, And thanks for the donation!

Yeah ethernat can be enabled, and the mouse not being recognized is similar to how a PS/2 mouse wont work unless plugged in from boot.

[danfoshizzle]

Yeah thanks for the donation pete, name had me stumped at first then i saw the p and the c lol

[pete]

Pac use the drivers for the NIC that I posted above in a link. They seemed to work better. Also unplug the NIC cable when first booting; as sometimes I think the NIC card itself is causing the stall in the boot. Once booted go and change the NIC speed. Reboot again without the cable. It should show up as not connected. Once you see this then just plug the cable in and you will see the interface looking for a DHCP address. If you leave the NIC to autonegociate then when you plug the cable in; it'll lock up.